در حال حاضر سایت در مرحله آزمایشی بوده و فروشها غیر فعال می باشد، از همراهی شما سپاسگذاریم و از نظرات سازنده شما استقبال می کنیم.

آجر شیشه ای ۲

آجر شیشه ای 2

شماره موضوع : ۰۰۹۵

فاصله بین آجر های شیشه ای با فاصله اندازهای مخصوص (spacer) ثابت نگه داشته می شود.

آجر شیشه ای 2

پس از اتمام کار، بندها مثل سنگ و سرامیک با سیمان سفید بند کشی میشود و باید بندکشی به صورتی انجام گیرد که بعدا ترک نخورد.

آجر شیشه ای 2

565

پر کن پیاله را، کین جام آتشین ... دیریست ره به حال خرابم نمی برد

دیدگاه کاربران
  • پیمان ۱۷ اسفند ۱۳۹۱ / ۹:۵۱ ق٫ظ

    خیلی عالی ممنون از زحمات شما

  • aligoolakh ۲ اسفند ۱۳۹۱ / ۴:۳۸ ق٫ظ

    Glass Block Mortar is a specifically formulated blend of white sand, cement, lime and other waterproof additives designed to provide a decorative, waterproof joint.
    APPLICATION
    Place a full bed of mortar onto the base or sill. Set the first course of
    glass blocks into the mortar. Adjust the blocks with a level to ensure
    straight lines upon completion. Tap blocks into place with a rubber
    mallet. Do not place Glass Block Mortar between glass
    blocks and expansion strips. Use a trowel to create recessed joints as
    work progresses. Follow the instructions of the glass block
    manufacturer for proper placement of anchors and spacers. With the
    proper use of spacers, it will be much easier to keep blocks level and
    ensure a more professional finished wall. Panel anchors and
    reinforcing bars should be spaced every 24″ (610 mm) vertically
    between glass blocks. The panel anchor is fastened through the
    expansion strip and into the jamb. Bend panel anchor horizontally into
    the joint and place reinforcing bars continuously from one side to the
    other. Apply half width of mortar into the joint and position reinforcing
    bars into mortar. Apply remaining mortar and lay the next course. Do
    not bridge expansion joints with panel reinforcing. Tool, rake, or finish
    joints before mortar reaches a final set.
    INSTALLATION
    SURFACE PREPARATION
    All framing, pocket recesses and chases must be accurately
    positioned and clean. Glass block must also be properly cleaned for
    best bond. Follow the instructions of the glass block manufacturer for
    best cleaning method. Coordinate the placement of anchors and
    glass block reinforcing bars and mark their positions. Expansion strips
    placed at the head and jambs should be held in place with a
    construction adhesive, such as Polyurethane
    Construction Adhesive. Allow to dry before block
    installation.
    MIXING
    Thoroughly mix Glass Block Mortar with clean water to a
    stiff plastic like consistency. Use 4–۵ quarts (3.8–۴.۷ L) of water per
    ۵۰ lb (22.7 kg) bag. Mix thoroughly for about 5 minutes. Stir material
    occasionally to keep mix workable; however, no additional water
    should be added. Acrylic Fortifier , diluted 1:1 with
    water, may be added in the place of water to ensure better water
    resistance, a stronger bond, improved curing, and less shrinkage.
    more info:
    http://www.simplyglassblocks.co.uk/install_rods.html

ترک ارسال پاسخ به aligoolakh لغو پاسخ

نشانی ایمیل شما منتشر نخواهد شد. بخش‌های موردنیاز علامت‌گذاری شده‌اند *

توسط
تومان